PlainEnviro

Guide

Lead in drinking water: what the rules require

EPA regulates lead in tap water through the Lead and Copper Rule. Instead of a limit for every sample, it sets an action level: when too many sampled homes are over it, the water system must act. A 2024 update lowers that level and requires lead pipes to be replaced.

How does EPA regulate lead in tap water?

Through the Lead and Copper Rule, which requires water systems to sample water at customers' taps. EPA's health goal for lead in drinking water is zero.

The rule compares the samples with two action levels: 0.015 milligrams per liter (15 parts per billion) for lead and 1.3 mg/L for copper. A system is over the action level when the 90th percentile of its samples is above it, which means more than 1 in 10 sampled taps was over.

The samples are taken at customers' taps, not at the treatment plant. The rule applies to community water systems and to non-transient non-community systems, which regularly serve at least 25 of the same people over six months a year.

Source: Lead and Copper Rule (EPA); Final LCRI: Rule Comparison Guide for Public Water Systems and Primacy Agencies (EPA, October 2024); 40 CFR 141.2, definitions (eCFR), read November 11, 2026.

What is a 90th percentile?

It is the result that 9 in 10 samples were at or under. Line up a round of tap samples from lowest to highest; the 90th percentile sits near the top of the line, with one in ten samples above it.

That means a 90th percentile under the action level does not say every home is low. Up to 1 in 10 sampled homes can be higher, and homes that were not sampled can differ.

What happens when a system is over the action level?

Going over the action level sets off required steps. Under the current rule, the system must take further steps to control corrosion, inform the public about how to protect their health, and may have to replace lead service lines under its control; since October 16, 2024 a lead action level exceedance also requires Tier 1 public notice within 24 hours.

Under the Lead and Copper Rule Improvements, the same duties apply at the lower action level: a system above it must install or re-optimize corrosion control treatment, run public education and, for lead, give Tier 1 public notice within 24 hours.

Source: Lead and Copper Rule (EPA); Final LCRI: Rule Comparison Guide (EPA, October 2024); Public Notification Rule (EPA), read November 11, 2026.

What changes under the Lead and Copper Rule Improvements?

The Lead and Copper Rule Improvements (LCRI) were published on October 30, 2024 and took effect on December 30, 2024. Systems must comply by November 1, 2027. Until then they follow the earlier rule, with some parts of the 2021 revisions, including the service line inventory.

Main changes from November 1, 2027
TopicWhat the LCRI requires
Lead action levelLowered to 0.010 mg/L (10 parts per billion) at the 90th percentile; the separate "trigger level" is removed. Copper stays at 1.3 mg/L.
Lead pipesReplace all lead and galvanized-requiring-replacement service lines under the system's control within 10 years, at an average of 10 percent a year, whatever the sample results. Replacement programs start by November 1, 2027.
Service line inventoryA baseline inventory by the compliance date, including connectors, updated every year and public, with a street address for each line.
Tap samplingAt homes with lead service lines, a first-liter and a fifth-liter sample after the water has sat at least six hours; the higher of the two counts.

Under the 2021 revisions, systems already had to prepare an initial lead service line inventory by October 16, 2024. A state can set a shorter replacement deadline, and some systems can qualify for a deferred one.

Source: National Primary Drinking Water Regulations for Lead and Copper: Improvements, final rule (Federal Register, October 30, 2024); Final LCRI: Rule Comparison Guide (EPA, October 2024); Final LCRI Technical Fact Sheet: Calculating Service Line Replacements (EPA, October 2024); Lead and Copper Rule Improvements (EPA), read November 11, 2026.

How do I read a system's lead results on PlainEnviro?

Open your water system from find by ZIP, drinking water by state or search. The page shows the system's latest lead and copper 90th percentiles from EPA's records, with the sampling period, against the action levels. EPA's national file holds these 90th-percentile results, not each home's sample.

Until November 1, 2027 the page compares lead with the current 0.015 mg/L action level. A result between 0.010 and 0.015 mg/L is under today's action level but would be over the LCRI level. Systems over the action level since 2020 are listed in lead over the action level. Lead and copper violations, such as a missed round of sampling, appear with the system's other violations.

Source: SDWA Data Download Summary and Data Element Dictionary (ECHO, EPA), read November 11, 2026.

How do I find out about lead at my own tap?

Ask your water system two things: whether your address has a lead or galvanized service line in its inventory, and whether it offers lead testing. For an independent test, use a laboratory certified for drinking water; EPA publishes contacts for each state's certification program. If you have questions about lead and your family's health, ask your doctor or your local health department.

Source: Final LCRI: Rule Comparison Guide (EPA, October 2024); Contact Information for Certification Programs and Certified Laboratories (EPA), read November 11, 2026.